THE BEST TRUCK WEIGHING SYSTEM

Onboard weighing system

Support

For more technical information write to:
 
[email protected]
 
Otherwise
 
 
 
 
Company Name 
 
Phone 
 
 
 
 

* Required
 
 
 

Frequently asked questions

 
Check that the orange LED on the hotspot is on permanently.

  • - If led off, check that the hotspot is properly plugged into the cigarette lighter, or press it in; in some cases it is necessary to turn the key  to power the cigarette lighter socket.
  • - If the LED is on, open the smartphone wifi settings page and check that you are connected to wifi W8Net_xxxxx network, otherwise repeat the pairing procedure; See the manual for more information.
In some cases it may be necessary to change the channel wifi hotspot, press and hold the orange button "CH SET" until you get the flashing orange LED: the number of flashes to identify the selected channel: 1 to 4.
Calibration is inhibited in case of failure of one or more sensors and automatically opens the diagnostics page.
After a period of inactivity (or on first use), you must wait at least 2 minutes of starting the application for the connection of all sensors.

  • - Run the App W8 and wait till the 2 red led and wait until the disappearance of the two red indicators.
  • - Briefly pressing the orange button located on the hotspot you can activate the awakening of the sensors without opening the app.

If the problem only affects some sensors verify the correct insertion of the batteries and / or their location in the vehicle: in some cases the installation at a disadvantage to the transmission of the radio signal might preclude the operation.
 
After a period of inactivity (or on first use), you must wait at least 2 minutes of starting the application for the connection of all sensors.

  • - Run the App W8 and wait till the 2 red led and wait until the disappearance of the two red indicators. 
  • - Briefly pressing the orange button located on the hotspot you can activate the awakening of the sensors without opening the app.

If the problem only affects some sensors verify the correct insertion of the batteries and / or their location in the vehicle: in some cases the installation at a disadvantage to the transmission of the radio signal might preclude the operation.
Open the Diagnostics page to verify which sensor has used batteries and replace them. Only use alkaline batteries.
The hotspot W8 works like any wifi hotspot: just select the network and enter the password to connect. Not being connected to the web, once associated with it you lose access to the Internet. And 'possible to overcome this in the following way:

iOS smartphone
  • - Open settings, Wi-Fi and select a network W8Net_xxxxx
    - Tap on the network to open the settings page
    - Tap on "STATIC" to change the type of network address
    - Enter the IP address 192.168.1.2 to the voice
    - Enter subnet mask 255.255.255.0 to the item.
    - Leave all fields Router and DNS
    - Tap on Wi-Fi on the top left to return to the settings.



Only for IOS
  •  
The calibration includes 4 stages 2 to be carried out with the exhaust means and the means 2 with a full load. If the display of a gross vehicle weight is not correct, you can repeat the calibration at any time by going to the half load on a weighing and repeating the second calibration operations (tractor trailer load and load).

There is a practical TARE function which allows you to reset any weight this residue in the middle drain, for example can be used to reset the net weight after refueling.
You can set at will the full scale of the bar, relative to gross vehicle weight. Go into settings, vehicle weight and enter the value to associate the 100%.
The W8 app allows you to set 2 different warning thresholds that trigger the overcoming of weight values defined.
These "alarms" can be used as alarm thresholds in the loading phase. Go into settings, data Warning or alarm data and enter the gross weight at which you want to activate the indicator.
It is possible display the weight in KG, Tonnes or Pounds.
Go into settings, Units and choose the desired unit. From this menu you can also set the resolution with 4 different roundingi.
Go into settings, Diagnostics to check the state of charge of the batteries of all sensors. A side indicator of each sensor will provide a clear indication of the charge level; in case of low battery the same will be red.
 
Back